View TC4066BP07_4115270.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TC4066BP/BF/BFN/BFT
TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic
TC4066BP,TC4066BF,TC4066BFN,TC4066BFT
TC4066B Quad Bilateral Switch
TC4066B contains four independent circuits of bidirectional switches. When control input CONT is set to "H" level, the impedance between input and output of the switch becomes low and when it is set to "L" level, the impedance becomes high. This can be applied for switching of analog signals and digital signals. * ON-resistance, Ron 250 (typ.): VDD - VSS = 5 V 110 (typ.): VDD - VSS = 10 V 70 (typ.): VDD - VSS = 15 V * OFF-resistance, Roff Roff (typ.) > 109
Note: xxxFN (JEDEC SOP) is not available in Japan. TC4066BP
TC4066BF
Pin Assignment
IN/OUT 1 OUT/IN 1 OUT/IN 2 IN/OUT 2 CONT 2 CONT 3 VSS
1 2 3 4 5 6 7 (top view)
14 13 12 11 10 9 8
VDD CONT 1 CONT 4 IN/OUT 4 OUT/IN 4 OUT/IN 3 IN/OUT 3 TC4066BFN
Truth Table
Control H L Impedance between IN/OUT-OUT/IN 0.5 to 5 x 10 >10
9 2
TC4066BFT
(Note)
Note:
See static electrical characteristics Weight DIP14-P-300-2.54 SOP14-P-300-1.27A SOL14-P-150-1.27 TSSOP14-P-0044-0.65A
: 0.96 g (typ.) : 0.18 g (typ.) : 0.12 g (typ.) : 0.06 g (typ.)
1
2007-10-01
TC4066BP/BF/BFN/BFT
Logic Diagram
1/4 TC4066B
I/O
O/I
CONT
Absolute Maximum Ratings (Note)
Characteristics DC supply voltage Control input voltage Switch I/O voltage Potential difference across I/O during ON Control input current Power dissipation Operating temperature range Storage temperature range Symbol VDD VCIN VI/O II/O ICIN PD Topr Tstg Rating VSS - 0.5 to VSS + 20 VSS - 0.5 to VDD + 0.5 VSS - 0.5 to VDD + 0.5 0.5 10 300 (DIP)/180 (SOIC) -40 to 85 -65 to 150 Unit V V V V mA mW C C
Note:
Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook ("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test report and estimated failure rate, etc).
Operating Ranges (VSS = 0 V) (Note)
Characteristics DC supply voltage Input voltage Symbol VDD VDD/VOUT Test Condition Min 3 0 Typ. Max 18 VDD Unit V V
Note:
The operating ranges must be maintained to ensure the normal operation of the device. Unused control inputs must be tied to either VDD or VSS.
2
2007-10-01
TC4066BP/BF/BFN/BFT
Static Electrical Characteristics (in case not specifically appointed, VSS = 0 V)
Test Condition Characteristics Symbol VDD (V) 5 Control input high voltage VIH |IIS| < 10 A 10 15 5 Control input low voltage VIL |IIS| < 10 A 10 15 On-state resistance On-state resistance (between any 2 switches) Input/output leakage current 0 VIS VDD RL = 10 k 5 10 15 5 RON 10 15 VIN = 18 V, VOUT = 0 V VIN = 0 V, VOUT = 18 V VIN = VSS, VDD (Note) VIH = 18 V VIL = 0 V 18 18 5 10 15 18 18 -40C Min 3.5 7.0 11.0 Max 1.5 3.0 4.0 800 210 140 100 100 0.25 0.50 1.00 0.1 -0.1 Min 3.5 7.0 11.0 25C Typ. 2.75 5.50 8.25 2.25 4.50 6.75 290 120 85 10 6 4 0.1 0.1 0.001 0.001 0.002 10-
5
85C Max 1.5 3.0 4.0 950 250 160 100 100 0.25 0.50 1.00 0.1 -0.1 Min 3.5 7.0 11.0 Max 1.5 3.0 4.0 1200 300 200 1000 1000 7.5 15.0 30.0 1.0 A -1.0 A V V Unit
RON
IOFF
nA
Quiescent supply current "H" level Input current "L" level
IDD
IIH IIL
-10-
5
Note:
All valid input combinations.
3
2007-10-01
TC4066BP/BF/BFN/BFT
Dynamic Electrical Characteristics (Ta = 25C, VSS = 0 V, CL = 50 pF)
Test Condition Characteristics Symbol VSS VDD (V) (V) 0 Phase difference between input to output I-O CL = 50 pF 0 0 Propagation delay time (control-OUT) tpZL tpZH RL = 1 k CL = 50 pF RL = 1 k CL = 50 pF RL = 1 k CL = 50 pF RL = 1 k CL = 15 pF RL = 10 k f = 1 kHz RL = 1 k RL = 1 k RIN = 1 k ROUT = 10 k CL = 15 pF CIN CIN-OUT Control input Switch I/O (Note 2) (Note 3) (Note 4) (Note 1) 0 0 0 0 0 0 0 0 0 -5 5 10 15 5 10 15 5 10 15 5 10 15 5 Min Typ. 15 8 5 55 25 20 45 30 25 10 12 12 30 Max 40 20 15 120 40 30 80 70 60 MHz MHz ns ns ns Unit
Propagation delay time (control -OUT)
tpLZ tpHZ
Max control input repetition rate
fmax (C)
-3dB cutoff frequency
fmax (I-O)
Total harmonic distortion -50dB feed through frequency -50dB crosstalk frequency Crosstalk (control-OUT)
-5 -5 -5 0 0 0
5 5 5 5 10 15

0.03 600 1 200 400 600 5 10 0.5
7.5
% kHz MHz
mV
Input capacitance Feed through capacitance
pF pF
Note 1: Sine wave of 2.5 p-p shall be used for Vis and the frequency of 20 log 10 Note 2: Vis shall be sine wave of 2.5 Vp-p Note 3: Sine wave of 2.5 Vp-p shall be used for Vis and the frequency of 20 log 10 feed-through. Note 4: Sine wave of 2.5 Vp-p shall be used for Vis and the frequency of 20 log 10 crosstalk.
VOS = -3dB shall be fmax. Vis
VOUT Vis VOUT Vis
= -50dB shall be
= -50dB shall be
4
2007-10-01
TC4066BP/BF/BFN/BFT
Circuit for Measurement of Electrical Characteristics
1. I-O
I/O-O/I I/O I/O O/I P.G. CL = 50 pF O/I I-O I-O VOH 50% 50% VOL 90% 50% 10% VDD WAVEFORM tr = 20 ns tf = 20 ns 90% 50% 10% VDD VSS
C
2. tpZH, tpHL, tpLZ, tpHZ
(CONTROL-OUT) VDD WAVEFORM tr = 20 ns tf = 20 ns 90% 50% 90% 50% 10% 90% tpHZ 50% tpZL VDD VSS VOH VOL VOH
Control I/O SW1 P.G. C RL = 1 k CL = 50 pF O/I SW2 O/I SW1 = VDD SW2 = VSS
10%
50% tpZH
O/I
SW1 = VSS SW2 = VDD
10% VOL tpLZ
3. RON
VDD
VIN
I/O
O/I VOUT RL = 10 k RON = 10 x (VIN - VOUT ) [k] VOUT
C
VSS
4. fmax (C)
VDD
tr = 20 ns
90% 50% 10%
tf = 20 ns 90% 10% 1 f 50% VSS VDD
O/I I/O P.G. C RL = 1 k CL = 50 pF
Control
O/I
VDD 2
5
2007-10-01
TC4066BP/BF/BFN/BFT
5. Crosstalk between Any Two Switches
VDD SWITCH ON
P.G.
I/O
O/I
C
RL = 1 k 2.5 V VSS VDD SWITCH OFF I/O
0V
-2.5 V I/O O/I VOUT RL = 1 k
RL = 1 k
C
VSS
6. Crosstalk, Control to Input
VDD tr = 20 ns 90% 10% tf = 20 ns 90% 10% VDD VSS
I/O
O/I
Control IN VOUT RL = 10 k CL = 15 pF
P.G. C
VOUT
RL = 1 k
7. Total Harmonic Distortion, fmax (I-O), Feedthrough
VDD 2.5 V I/O O/I VOUT I/O IN
P.G.
0V
C
CL
RL
-2.5 V
1 f
VSS
6
2007-10-01
TC4066BP/BF/BFN/BFT
Package Dimensions
Weight: 0.96 g (typ.)
7
2007-10-01
TC4066BP/BF/BFN/BFT
Package Dimensions
Weight: 0.18 g (typ.)
8
2007-10-01
TC4066BP/BF/BFN/BFT
Package Dimensions (Note)
Note:
This package is not available in Japan.
Weight: 0.12 g (typ.)
9
2007-10-01
TC4066BP/BF/BFN/BFT
Package Dimensions
Weight: 0.06 g (typ.)
10
2007-10-01
TC4066BP/BF/BFN/BFT
RESTRICTIONS ON PRODUCT USE
* The information contained herein is subject to change without notice.
20070701-EN GENERAL
* TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the "Handling Guide for Semiconductor Devices," or "TOSHIBA Semiconductor Reliability Handbook" etc. * The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ("Unintended Usage"). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer's own risk. * The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. * The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. * Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations.
11
2007-10-01

▲Up To Search▲

Price & Availability of TC4066BP07

	To Download TC4066BP07 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .